how to measure a door latch

February 16, 2022

Measure the diameter of the holes currently cut out of your door so you can select a new door lock that fits those dimensions. When replacing or newly installing a door lock there are measurements you need to know before you place an order on your lock.

A Guide To Choose The Right Tubular Latch Our Blog

Take care to measure carefully as matching the size can be especially problematic in older homes.

. Guide to Door Lock Measurements. A standard thickness for an interior door is 1-34 Measure the location of all 3 hinges. Measure the height of the door right in the middle.

An easy way to choose which latch you need is to measure from the edge of your door to the centre of your door Stile. This will determine the housing height also called the barrel length. Look for the size down the right hand column of the upvc door handles table below size C show in the diagram.

Upvc Door Locks and Multipoint Replacement UPVC Door Locks can be purchased from UPVC Spares 4 Repairs here. Measure the width of the door in 3 locations. How to Measure Backset And Width Door Measurements For Door Hardware.

If you must it is always better to round down than round up. For the most accurate measurement remove the door. No welding Made in the USA bear jaw latches.

The latch faceplate will sit in this recession. Before you learn how to change door locks measure the space where youll install the replacement. This dimension ensures a snug fit.

Measure from the floor to the underside of the trim at the top of the door. Bore a 1-inch hole in the edge of the door located on the centerline of the 2-18-inch hole. There are 3 main sizes to take when measuring a door handle.

The latch will fit into the 1-inch hole. Choose the Backset which is closest to this measurement and the handle will be as central as possible to the Stile on your door. Use a tape measure and be as accurate as you can millimetres please and make sure the measurement is taken from the centre of each screw.

Next is the distance between the centre of the top screw to the centre of the bottom screw. Lock BoreThe diameter of the hole for the lock body. The first is the distance from the centre of the handle to the centre of the keyhole.

If the size is missing then contact us with the sizes you have measured. Measure the width and height of each hinge. To obtain these measurements measure down from the top of the door to the top of each hinge.

If you dont have any hardware on your door just measure from the edge of the door to the center of the bore hole the large hole where the door knob assembly is mounted. The standard bore is 2-18. This video is about how to fit a door latch and door handle in an interior door.

Chisel out a 1-inch-by-2-14-inch rectangle on the edge of the door 18 of an inch deep. Once you have found size C then check that. Tools needed for this job.

This helps to ensure that your door will fit. Using a ruler or tape measure hold the end of the tape or rule against the flat edge of the catch and measure the distance from the catch to the edge of the door. This is sometimes called the pz.

Finally the length of the handle plate top to bottom. Measure the distance from the top of the door to the center of the bore hole for the handle. Works with your original handles.

The measure that is really important when choosing latches is the cut out measurement. If you take off one of the latches and measure the cut out then you can. The most common backset is 2 38 but 2 34 is also quite common - usually used on exterior doors.

Measuring the distance of the latch from the edge of the door so that measurement can be transferred to door frame. The latch bore can be found on the edge of the door and its standard size is 2 18 inches. Determine the distance between the outer surface of the door and the inner surface of the enclosure where the cam will make contact.

In either case this is one of the first dimensions you need to properly size the cam lock. If the cut outs on your truck are 5-14 x 6-12 for the latch then we do not carry a fit because Paddle Handle Locking Latch w Release part PLR5115 is the latch with the largest cut out available at 4-58 long x 3-38. Use the smallest figure as your measurement.

Tape measure pencil flat drill bit. Standard backsets are either a 2 38 backset or 2 34 backset. Ad Its easy to bolt-on safer better working door latch upgrades for your Classic Truck.

Also measure the doors backset which is the length straight from the. Back Set Will be 2 and 38 inch residential or 2 and 34 inch commercial.

Measuring For A Door Latch Willow And Stone Willow And Stone